ROMABIO’s LowSatin Urethane is the alternative for traditional oil paint finishes. These products are the lowest toxic chemical, water-based urethane alkyds on the market. It is a surface application urethane, with high durability & performance, and designed to resist most environmental conditions. For Interior/Exterior use.
LowSatin Urethane is a ROMABIO Environmental Low Impact LOW-Series Product.
1 Identification of the Substance/Mixture & 0f the Company/Undertaking
1.1 Product Identifier
Code None
Product Name EcoSatin Urethane Alkyd
1.2 Relevant Identified Uses of the Substance or Mixture & Uses Advised Against
Intended Use Refer to Data Sheet
1.3 Details of the Supplier of the Safety Data Sheet
- Name ROMABIO – Eco-Sustainable Building Technologies
- Full Address 554 North Avenue NW, Suite B
- District & Country Atlanta, GA 30318 | United States of America (USA)
- 678-905-3700
1.4 Emergency Telephone Number
For Urgent Inquiries Refer To Call 911 if you have a poison emergency.
Call the CDC if swallowed but person is alert 1-800-222-122
2 Hazards Identification
2.1 Classification of the Substance or Mixture
CLASSIFICATION ACCORDING TO DIRECTIVE 67/548/EEC OR 1999/45/EC
May produce an allergic reaction.
This mixture does not present physical hazards. Refer to the recommendations regarding the other products present on the site.
This mixture does not present health hazards.
This mixture does not present a danger to the environment. No damage to the environment known or expected under normal use.
2.2 Label Elements
The product is classified and labeled according to EC directives or corresponding national laws.
LABELING (67/548/EEC or 1999/45/EC)
HAZARD STATEMENTS
Contains EC 205-250-6 BIS (2-ethylhexanoate) DE COBALT. May produce an allergic reaction.
Safety phrases
- S29 Do not empty into drains.
2.3 Other Hazards
Information not available.
3 Composition/Information on Ingredients
3.1 Substances
No substance fulfills the criteria set out in Annex II, Part A of the REACH Regulation (EC) n. 1907/2006.
3.2 Mixtures
Identification | Conc. % | Class. 67/548/EEC | Class. 1272/2008 (CLP) |
---|---|---|---|
ZINC OXIDE | |||
CAS 215-222-5 | |||
EC 030-013-00 | 0 < = x % < 1 | ||
INDEX 1314-13-2 | |||
NAPHTA LOURD, OIL HYDROTREATED | |||
CAS 64742-48-9 | |||
EC 649327006 | 0 < = x % < 1 | ||
INDEX 265-150-3 | |||
BIS (2-ETHYLHEXANOATE) OF COBALT | |||
CAS 136-52-7 | |||
EC 136527 | 0 < = x % < 1 | ||
INDEX 205-250-6 |
T+ = Very Toxic (T+), T = Toxic(T), Xn = Harmful (Xn), C = Corrosive (C), Xi = Irritant (Xi), O = Oxidizing (O), E = Explosive(E), F+ = Extremely Flammable(F+), F = Highly Flammable(F), N = Dangerous for the Environment (N)
ADDITIONAL INFORMATION
Full text of R-phrases: see section 16.
Full text of H-phrases: see section 16.
4 First Aid Measures
4.1 Description of First Aid Measures
In all cases of doubt, or when symptoms persist, seek medical advice. In case of unconsciousness give nothing by mouth, place in unconscious position and seek medical advice.
- AFTER INHALATION Toxicological data are not available.
- IN CASE OF SKIN CONTACT Toxicological data are not available.
- IN CASE OF EYE CONTACT Toxicological data are not available.
- AFTER INGESTION Toxicological data are not available.
4.2 Most Important Symptoms & Effects, Both Acute & Delayed
Toxicological data are not available.
4.3 Indication of Any Immediate Medical Attention & Special Treatment Needed
Toxicological data are not available.
5 Firefighting Measures
5.1 Extinguishing Media
SUITABLE EXTINGUISHING MEDIA
Alcohol resistant foam, Carbon dioxide, Powder, spray mist, (water).
EXTINGUISHING MEDIA WHICH SHALL NOT BE USED FOR SAFETY REASONS
Strong water jet.
5.2 Special Hazards Arising From the Substance or Mixture
HAZARDS CAUSED BY EXPOSURE IN THE EVENT OF FIRE
Do not breathe combustion products (Carbon Oxide, Toxic Pyrolysis Products, etc.).
5.3 Advice for Firefighters
Provide a conveniently located respiratory protective device.
ADDITIONAL INFORMATION
Cool closed containers that are near the source of the fire. Do not allow water used to extinguish fire to enter drains, ground or waterways. Treat runoff as hazardous.
6 Accidental Release Measures
6.1 Personal Precautions, Protective Equipment & Emergency Procedures
Ventilate affected area. Do not breathe vapors. See protective measures under point 7 and 8.
6.2 Environmental Precautions
Do not allow to enter into surface water or drains. If the product contaminates lakes, rivers or sewages, inform competent authorities in accordance with local regulations.
6.3 Methods & Material for Containment & Cleaning Up
Isolate leaked material using non-flammable absorption agent (e.g. sand, earth, vermiculite, diatomaceous earth) and collect it for disposal in appropriate containers in accordance with the local regulations (see chapter 13). Clean using cleansing agents. Do not use solvents.
6.4 Reference to Other Sections
Observe protective provisions (see chapter 7 and 8).
7 Handling & Storage
7.1 Precautions for Safe Handling
ADVICES ON SAFE HANDLING
The usual precautionary measures for handling chemicals should be observed.
PRECAUTIONS AGAINST FIRE AND EXPLOSION
No special measures are required.
7.2 Conditions for Safe Storage, Including Any Incompatibilities
REQUIREMENTS FOR STOREROOMS AND CONTAINERS
No special measures are required. Keep container tightly closed. Store carefully closed containers upright to prevent any leaks.
HINTS ON JOINT STORAGE
Keep away from strongly acidic and alkaline materials as well as oxidizers.
FURTHER INFORMATION ON STORAGE CONDITIONS
Keep away from frost! Keep only in the original container in a cool, well-ventilated place. Take care of instructions on label.
7.3 Specific End Use(s)
Observe technical data sheet. Observe instructions for use.
8 Exposure Controls/Personal Protection
8.1 Control Parameters
CAS | TWA | STEL | CEILING | DEFINITION | CRITERIA |
---|---|---|---|---|---|
mg/m3 | mg/m3 | ||||
1314-13-2 | 2 | 10 | – | – | R |
ADDITIONAL INFORMATION
- TWA (EC) Occupational exposure limit value.
- STEL (EC) Short-term occupational exposure limit value.
8.2 Exposure Controls
Provide good ventilation.
RESPIRATORY PROTECTION
No special measures are necessary. Do not inhale vapors or mist.
HAND PROTECTION
Wear protective gloves. Suitable material: NBR (Nitrile rubber).
EYE PROTECTION
Wear closely fitting protective glasses in case of splashes.
PROTECTIVE MEASURES
After contact clean skin thoroughly with water and soap odor use appropriate cleanser.
ENVIRONMENTAL EXPOSURE CONTROLS
Do not allow to enter into surface water or drains. refer to chapter 7. No further action is necessary.
9 Physical & Chemical Properties
9.1 Information on Basic Physical & Chemical Properties
Appearance | Liquid |
Color | Refer to Label |
Odor | Characteristic |
Odor Threshold | – |
pH | Neutral |
Melting or Freezing Point | – |
Boiling Point | – |
Distillation Range | – |
Flash Point | – |
Evaporation Rate | – |
Flammability of Solids & Gases | – |
Lower Inflammability Limit | – |
Upper Explosive Limit | – |
Lower Explosive Limit | 0.8% |
Vapor Pressure | – mbar |
Vapor Density | – g/cm3 |
Specific Gravity | 1.455 Kg/lt |
Solubility | Partially Soluble |
Solvent Separation Test | < 3% |
Solid content | 69% by Weight |
Partition Coefficient: Octanol/Water | – |
Ignition Temperature | – |
Decomposition Temperature | – |
Viscosity at 23°C | 15 s 6 mm |
Reactive Properties | – |
9.2 Other information
VOC (Directive 2004/42/EC) | 67.00 g/lt |
VOC (volatile carbon) | – |
Organic Solvents | – |
Water | Soluble |
Matt coatings for interior walls and ceilings. EU limit value for this product
(cat. A/a): 75 g/lt (2007) / 30 g/lt (2010).
10 Stability & Reactivity
10.1 Reactivity
Information not available.
10.2 | Chemical Stability
Stable when applying the recommended regulations for storage and handling. Further information on correct storage: refer to chapter 7.
10.3 Possibility of Hazardous Reactions
Keep away from strong acids, strong bases and strong oxidizing agents to avoid exothermic reactions.
10.4 Conditions to Avoid
Stable when applying the recommended regulations for storage and handling. Further information on correct storage: refer to chapter 7. Hazardous decomposition byproducts may form with exposure to high temperatures.
10.5 Incompatible Materials
Information not available.
10.6 Hazardous Decomposition Products
Hazardous decomposition by products may form with exposure to high temperatures, e.g.: carbon dioxide, carbon monoxide, smoke and nitrogen oxides.
11 Toxicological Information
11.1 | Information on Toxicological Effects
ACUTE TOXICITY
Toxicological data are not available.
IRRITANT AND CORROSIVE EFFECTS
Toxicological data are not available.
SENSITIZATION
Toxicological data are not available.
SPECIFIC TARGET ORGAN TOXICITY
Toxicological data are not available.
ASPIRATION HAZARD
Toxicological data are not available.
CMR EFFECTS (CARCINOGENICITY, MUTAGENICITY AND TOXICITY FOR REPRODUCTION)
Toxicological data are not available.
PRACTICAL EXPERIENCE
Other Observations
Repeated or prolonged contact with the preparation may cause removal of natural fat from the skin resulting in non-allergic contact dermatitis and/or absorption through skin. Splashing may cause eye irritation and reversible damage.
OVERALL ASSESSMENT ON CMR PROPERTIES
The components in this formulation do not meet the criteria for classification as CMR category 1 or 2.
There is no information available on the preparation itself . The preparation has been assessed following the conventional method of the Dangerous Preparations Directive 1999/45/EC and has not been classified.
12 Ecological Information
There is no information available on the preparation itself. Do not allow to enter into surface water or drains.
12.1 Toxicity
Toxicological data are not available.
12.2 Persistence & Degradability
Toxicological data are not available.
12.3 Bioaccumulative Potential
Toxicological data are not available.
12.4 Mobility in Soil
Toxicological data are not available.
12.5 Results of PBT & vPvB assessment
Toxicological data are not available.
12.6 Other Adverse Effects
Toxicological data are not available.
13 Disposal considerations
13.1 Waste Treatment Methods
APPROPRIATE DISPOSAL / PRODUCT
RECOMMENDATION
Do not allow to enter into surface water or drains. This material and its container must be disposed of in a safe way. Waste disposal according to EC directives 75/442/EEC and 91/689/EEC in the corresponding versions, covering waste and dangerous waste.
CONTROL REPORT FOR WASTE CODE / WASTE MARKETING ACCORDING TO EAKV
080111 Waste paint and varnish containing organic solvents or other dangerous substances
CONTAMINATED PACKAGING
RECOMMENDATION
Cleaned containers may be recycled. Vessels not properly emptied are special waste.
14 Transport Information
This mixture is not classified as dangerous according to international transport regulations (ADR/RID, IMDG,
ICAO/IATA).
No dangerous good in sense of these transport regulations.
14.1 UN-NO
Information not available.
14.2 UN PROPER SHIPPING NAME
Information not available.
14.3 TRANSPORT HAZARD CLASS(ES)
Information not available.
14.4 TRANSPORT HAZARD CLASS(ES)
- LAND TRANSPORT (ADR/RID) –
- SEA TRANSPORT (IMDG) –
- AIR TRANSPORT (ICAO-TI / IATA-DGR) III
14.5 ENVIRONMENTAL HAZARDS
- LAND TRANSPORT (ADR/RID)
- MARINE POLLUTANT
14.6 SPECIAL PRECAUTIONS FOR USER
Transport always in closed, upright and safe containers. Make sure that persons transporting the product know what to do in case of an accident or leakage. Advices on safe handling: see parts 6 – 8.
FURTHER REMARKS
LAND TRANSPORT (ADR/RID)
TUNNEL RESTRICTION CODE
SEA TRANSPORT (IMDG)
EMS-NO.
14.7 TRANSPORT IN BULK ACCORDING TO ANNEX II of MARPOL 73/78 AND THE IBC CODE
Information not available.
15 Regulatory Information
15.1 Safety, Health & Environmental Regulations/Legislation Specific for the Substance or Mixture
ACCORDING TO EU-REGULATION 2004/42/EC (APPENDIX II)
EU LIMIT VALUE FOR THIS PRODUCT
Paints and wood stains for interior and exterior
150 g/lt (2007) / 130 g/lt (2010). This product contains 5.47 g/lt VOC
NATIONAL REGULATIONS
INFORMATIONS ON WORKING LIMITATIONS
Observe employment restrictions under the Maternity Protection Directive (92/85/EEC) for expectant or nursing mothers. Observe restrictions to employment for juveniles according to the ‘juvenile work protection guideline’ (94/33/EC).
15.2 Chemical Safety Assessment
Chemical safety assessments for substances in this preparation were not carried out.
16 Other Information
GENERAL BIBLIOGRAPHY
Relevant R-and H-phrases (Number and full text):
- The Merck Index. Ed. 10
- Handling Chemical Safety
- Niosh – Registry of Toxic Effects of Chemical Substances
- INRS – Fiche Toxicologique
- Patty – Industrial Hygiene and Toxicology
- N.I. Sax – Dangerous properties of Industrial Materials-7 Ed., 1989
Note FOR USERS
The information supplied on this safety data sheet complies with our current level of knowledge as well as with national and EU regulations. Without written approval, the product must not be used for purposes different from those mentioned in chapter 1. It is always the user’s duty to take any necessary measures for meeting the requirements laid down by local rules and regulations. The details in this safety data sheet describe the safety requirements of our product and are not to be regarded as guaranteed attributes of the product.
FIELDS OF APPLICATION
Excellent finish paint for interior and exterior applications on all types of materials. EcoSatin Urethane is an alkyd oil paint alternative with exceptionally high UV resistance, high resistance to atmospherically conditions, and is applicable in residential, commercial, marine, and industrial environments. Product can be applied to iron, aluminum, steel, galvanized steel, concrete, tile, glass, all types of caulks, wood, plastic and sheetrock. EcoSatin Urethane is a Gloss level 4 finish, which when dried, creates a highly scratch resistant surface, suitable for floors, cabinets, doors, etc., where durability is a priority. EcoSatin Urethane is both waterproof and oil proof. This product is a water based urethane paint product providing superior adhesion than typical oil, acrylic, or waterborne paints.
EcoSatin Urethane can be used with or without a primer based on pre-existing conditions, type of finish desired and type of material to be painted.
PRODUCT FEATURES
A 100% urethane alkyd paint product, non permeable, provides good anchoring power, with excellent resistance to scratches, water, and oils. Product is diluted with water, has very low odor, easy to apply, mimicking traditional oil or lacquer paints, low drip/paint run ratio, with elastic capabilities suitable for exterior wood surfaces. Product is considered an earth friendly product, ideal for use in homes, schools, and hospitals, and work sensitive areas.
This paint product is an oil proof, washable finish that cannot be damaged by foods, greases, body oils, color crayons or washable colored markers. Cleaning does not change the sheen of the paint. Paint touch-ups are simple but may require whole wall repaints, particularly for sprayed finishes.
EcoSatin Urethane is specifically designed to be tinted with natural oxide earth tints and 0% VOC colorants to increase esthetic color values with minimal impact to the environment and to provide toxic free air quality for indoors. EcoSatin Urethane is an Environmental Low Impact paint material as described in the Eco Category description.
TYPE OF PRODUCT
Urethane alkyd coating with organic stabilizers.
SHEEN FINISH
Satin
COLOR
White/Transparent Base. Color tint up to 8% max with approved tints for white base, 15% max with approved tints for transparent base. Custom color tint matching available.
APPLICATION CYCLE INSTRUCTIONS
BRUSH AND ROLLER APPLICATIONS
1ST COAT Dilute EcoSatin Urethane typically with 10% water, 250 ml to one (1) 2.5-liters bucket, maximum 15% water, 375 ml to one (1) 2.5-liters bucket of EcoSatin Urethane. For better coverage and sheen results it is advised to prime surfaces with a universal urethane primer or EcoPrimer Urethane for wood. It is not advised to use roller application except when necessary, as the roller nap may create an undesirable finish. An appropriate sprayer will use less material and create highly desirable finishes. Hand brush work will create a typical oil paint finish, that reflects visible brush strokes. Allow to dry for at least 4 – 8 hours before applying 2nd coat, if required. 1st coat must be dry before applying 2nd coat. Wash paint brushes immediately with soap and water after completion of use. Do not allow paint brushes to stand outside beyond 5 – 10 minutes. Rinse brushes immediately with water or stand in water during short painting breaks.
2ND COAT Dilute EcoSatin Urethane same as above. A 2nd coat is not necessary usually when using a correctly tinted primer base. Apply paint in an even and constant pattern, so that a perfect coverage is achieved. For repaints with light colors on dark colors, at least 2 finish coats will be required. Metal surfaces that are pre-primed will not require a urethane primer, but will require 2 coats for adequate coverage. Handling time after painting varies according to ambient conditions, typical time is 2 – 4 hours for light touching. Allow EcoSatin Urethane approximately 72 – 144 hours to achieve complete hardness.
PAINT SPRAYERS
1ST COAT Dilute EcoSatin Urethane typically with 10% water, 250 ml to one (1) 2.5-liters bucket, maximum 15% water, 375ml to one (1) 2.5-liters bucket of EcoSatin Urethane. Using a good quality sprayer is imperative. Best results can be achieved using either a compressor siphon feed spray guns, or a high quality airless sprayer for fine finishes, with high and low pressure options. A professional spray application will consume less material and create very desirable finishes and sheens.
2ND COAT Dilute EcoSatin Urethane same as above. A 2nd coat is not necessary usually when using a correctly tinted primer base. If the paint has not been applied in an even and constant pattern to create a perfect coverage, a 2nd coat will be required. 1st coat must be dry before applying 2nd coat. For repaints with light colors on dark colors, at least 2 finish coats will be required. Metal surfaces that are pre-primed will not require a urethane primer, but will require 2 coats for adequate coverage. Handling time after painting varies according to ambient conditions, typical time is 2 – 4 hours for light touching. Allow approximately 72 – 144 hours for paint to achieve complete hardness.
Manufacturer recommends that a universal urethane primer or EcoPrimer Urethane is lightly and carefully sanded to create excellent finish results when spraying EcoSatin. Clean all surfaces to be painted carefully before application of final coat with a sprayer. Insure that the area to be painted is free of dust, prior to and after painting for several days.
SPRAY TIP USAGE Apply paint product with a # 0.011 – 0.013 mm size spray tip for airless sprayers, and for compressor spray guns check with manufacturer. Always use new spray tips for starting a paint job for best results. This will also conserve the amount of paint necessary to complete the job. Note* It is not advised to rest an airless spray gun without use for over 15 minutes without use, as water-based urethane paint may partially dry and clog in spray gun or pistol. If this occurs, flush out sprayer with denatured alcohol or lacquer thinner several times to remove clogged guns or tips, and then flush several times with water to remove solvent cleaning materials. For best spray results and finishes, it is recommended to use a Kremlin Rexson Pump with an Excite spray gun.
MIXING PAINT & WATER
Most of our paint formulas are concentrated and require water to be added to them for proper use. This process means we can sell more coverage in an economical package that decreases the cost for transport, reduces the carbon footprint, helping the your pocket book and the environment.
Mix paint and water with an electric drill and paint paddle, or mix well by hand! If water is sitting on the top of your mixture, the paint is not properly mixed!
Apply with brush, roller or with the an appropriate sprayer and sprayer tip. New sprayer tips should be used to prevent product waste and provide for a more perfect finish.
TOOLS
Apply with brush, roller or with the an appropriate sprayer.
DRYING TIME
Allow a drying time between coats of at least 4 – 8 hours. With lower temperature and humidity more time may be needed. If sanding is required between coats, drying time permitted may increase – 24 hours before light sanding depending on humidity and environmental conditions. Allow 72 – 144 hours to achieve complete hardness. Product requires 14 days for 100% full curing time.
CONSUMPTION/COVERAGE
Approximately 400 ft2 / 37 mt2 per 2.5 liters bucket diluted with 250ml water (10%) when applied by brush. Approximately 530 ft2 / 49 mt2 per 2.5 liters bucket diluted with 250ml (10%) water when applied with sprayer. Determine exact consumption by performing a test on the surface to be treated.
PACKAGING
Plastic buckets of 1 and 2.5 liters.
APPLICATION CYCLES ON DIFFERENT TYPES OF BASES
Make sure base is solid, dry and well cleaned, prepared with skill. It is recommended to observe the rule VOB DIN 18 363, Part C, paragraph 3. All exterior painted surfaces should be checked on a regular basis after 4 – 5 years to ensure that the paint product has remained intact, without damages, cracks, or fading, and if so repaints should be made immediately. After 7 – 8 years all exterior painted surfaces should be re-painted so as to maintain the quality of the original surface and not permit damage or decay to the urethane paint.
NEW SHEETROCK
Prime all new sheetrock with 2 coats EcoDomus Matte, sanding lightly between coats, using a paint sprayer for application. Allow primer paint to dry for at least 8 hours. Apply 1 coat of EcoPrimer Urethane with a paint sprayer, and allow to dry for at least 4 hours, and then lightly sanding. Remove all dust from area to be painted. Lightly wipe wall surfaces with a damp cloth or tack cloth to remove all traces of dust. Apply EcoSatin Urethane according to instructions.
PAINTED SHEETROCK
Lightly sand all surfaces prior to applying 1 coat of EcoPrimer Urethane with a paint sprayer, and allow to dry for at least 4 hours, and then lightly sand. Remove all dust from area to be painted. Lightly wipe wall surfaces with a damp cloth or tack cloth to remove all traces of dust. Apply EcoSatin Urethane according to instructions.
UNPAINTED WOOD
Sand all wood surfaces as required to provide a smooth surface. Fill all nail and screw holes with non-oil type putty or wood filler. Apply 1 coat of EcoPrimer Urethane with a brush or a paint sprayer, and allow to dry for at least 4 hours. Apply water based caulk as needed to fill all voids and cracks. Paint all caulked areas as needed and allow to dry for at least 12 hours. Lightly sand all surfaces and remove all dust from area to be painted. Lightly wipe wood surfaces with a damp cloth or tack cloth to remove all traces of dust. Apply EcoSatin Urethane according to instructions.
EcoSatin Urethane can also be applied to any type of wood without using a primer. This component results in a type of architectural/decorative finish, in that it highlights the wood grains inherent in the woods, yet providing the same high quality engineering, with the same quality sheens as is created using a wood primer.
PAINTED WOOD
Sand all painted wood surfaces as required to provide a smooth surface. Fill all nail and screw holes with non oil type putty or wood filler. Apply water based caulk as needed to fill all voids and cracks. Paint all caulked areas as needed and allow to dry for at least 12 hours. Apply 1 coat of EcoPrimer Urethane with a brush or a paint sprayer, and allow to dry for at least 4 hours, then lightly sand. Remove all dust from area to be painted. Lightly wipe wood surfaces with a damp cloth or tack cloth to remove all traces of dust. Apply EcoSatin Urethane according to instructions.
It is not a requirement to prime painted wood if the quality of the finish is acceptable to create a perfect finish. EcoSatin Urethane will read any non desirable textures existing on the wood surfaces.
STEEL/IRON/GALVANIZED STEEL/ALUMINUM
Sand all metal surfaces to provide a rust free and smooth surface as is possible, previously painted or non-painted. For unprimed metal surfaces, apply 1 coat of EcoMetal Urethane and allow to dry for 12 hours. Apply EcoSatin Urethane applying with a brush or sprayer as indicated in the instructions above. For exterior metal surfaces, it is advised to apply two (2)-coats of EcoSatin Urethane onto primed or painted surfaces. EcoSatin Urethane can be painted onto solvent based metal primers, ensuring that such primer is completely dry before painting. On large flat areas it is advised to spray paint all surfaces. For small areas or detail work use a high quality finish paint brush to ensure a smooth a finish.
After 2 years, it is advised to inspect exterior painted metal surfaces, particularly previously painted surfaces that were painted with ‘other’ types of enamel paint. If rust has appeared, address damaged areas and remove rust as is possible and apply EcoMetal Urethane as directed, and then 1 coat of EcoSatin Urethane as directed above.
For all metal surfaces, it is advised after 4 – 5 years to make careful inspection of interior and exterior painted surfaces and if EcoSatin Urethane is beginning to fade, or show signs of distress, or wear, it is advised to prime all areas where the finish surface has been removed by chips, scratches, or damages, sanding those areas lightly to provide an even surface and apply 1 coat of EcoSatin Urethane to re-protect surfaces and provide a new painted finish.
If after 7 – 8 years regardless of the lack of damages, stress, or fading, all exterior painted surfaces should be repainted so as to protect the original painted surface and ensure additional trouble free service of a high quality paint finish.
TILE
Clean all surfaces carefully, removing all soap films, mold, dirt, and apply 2 coats EcoSatin Urethane directly onto the tile surface. It is advised to apply the paint with a good quality paint sprayer for best results. We do not advise to paint shower walls, enamel tubs or sinks where aggressive cleaning may damage the surface. This application should be used solely as an architectural covering for decorative purposes only.
GLASS
Clean off glass surfaces as required to obtain a clean oil free surface and apply 2 coats EcoSatin Urethane directly onto the glass surface. It is advised to apply the paint with a good quality paint sprayer best results.
CAULKS
EcoSatin Urethane will adhere to most solvent based caulks, acrylic caulks and some silicone based caulks. Always test product for adhesion verification prior to painting any surface.
PLASTIC
Remove all dirt, oils, glues, as required to provide a clean surface. Lightly sand or steel wool surface as may be necessary to create a slightly opaque surface. Painting preferences will determine method of application. For thicker types of paint applications apply 1 coat of a universal urethane primer, and 2 coats of EcoSatin Urethane. For thinner types of paint applications, apply 2 coats of EcoSatin Urethane directly onto surface. It is advised to apply the urethane paint with a good quality paint sprayer for best results.
NEW CEMENT STUCCOS
New cement should not be painted for about 28 days to ensure proper anchoring and drying. Apply 1 coat of EcoForte Consolidator diluted 50% (2:1) with water, and allow to dry for at least 12 hours. Apply 1 coat of universal urethane primer and allow to dry for 8 – 12 hours. Apply final paint finish with EcoSatin Urethane according to instructions.
DECAYING OR CRUMBLING STUCCOS OR POWDERY SURFACES
Chalking surfaces, which could prevent the proper anchoring of the base coating must be removed and pressure washed. Apply Potassium Silicate Concentrate, diluted 100% with water (1:1) on all damaged surfaces, applying 2 – 3 coats in rapid succession and allow to dry for at least 12 hours. Apply 1 coat of EcoForte Consolidator diluted 50% with water, and allow to dry for at least 12 hours. Apply 1 coat of universal urethane primer and allow to dry for 8 – 12 hours. Apply final paint finish with EcoSatin Urethane according to instructions.
COATINGS WITH EFFLORESCENCE
Cement surfaces showing efflorescence should be removed with acid and thoroughly rinsed with water. Apply Potassium Silicate Concentrate, diluted 100% with water (1:1) on all damaged surfaces, applying 2 – 3 coats in rapid succession and allow to dry for at least 12 hours. For coatings on surfaces damaged by the saltpeter or efflorescence no guarantees can be provided. Apply 1 coat of EcoForte Consolidator diluted 50% with water, and allow to dry for at least 12 hours. Apply 1 coat of universal urethane primer and allow to dry for 8 – 12 hours. Apply final paint finish with EcoSatin Urethane according to instructions.
AGED CEMENT STUCCOS
When new stucco repairs are performed on older cement stuccos, apply EcoForte Consolidator diluted 50% with water (2:1), to older surfaces prior to applying new cement stucco. Dirty and/or contaminated surfaces should be cleaned and any attached algae removed manually or by mechanical means, i.e., with a high-pressure washer. Stucco damaged by algae or mold should be treated with EcoDis. Apply 1 coat of universal urethane primer and allow to dry for 8 – 12 hours. Apply final paint finish with EcoSatin Urethane according to instructions.
STUCCO REPAIRS
See Aged Cement Stuccos above.
STORAGE
Store in a cool, dry and protected from frost. Close the open containers with care. Store liquids only
in plastic.
WARNING!
Do not apply any products in direct exposure to strong/hot sunlight, rain, high humidity (mist) or in the presence of strong wind. Beware of the danger of frost overnight. If applied by roller or sprayer, protect surrounding surfaces as necessary. Protect eyes and skin from splashes of paint. Cover glass, ceramic, natural stone, brick, metal, wood, painted surfaces and glazed tiles. Clean affected areas immediately with water. Prominent elements of the building (cornices, parapets, etc.,) should be treated with skill, covering flashings, gutters, copper coatings, etc.
Do not work in air temperature lower than 13°C / 55°F and not above 31°C / 88°F. Clean work tools with water immediately after use. Keep out of reach of children. In case of contact with eyes and skin, wash immediately with plenty of water. In cases of consumption, consult a Doctor or call the CDC Poison Center.
WATER CONTAMINATION HAZARD
Class 1 This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all of information required by the CPR, and it is classified as a non-hazardous material.
PRODUCT CONTAMINATION HAZARD
CODE CER / NORMATIVE EAC / Decision commuted by the Commission n. 2000/532/CE
NOT DANGEROUS The directive 75/442/CEE, 08 01 production, disposal, formulation, supply, use, and removal of paints and varnishes: 10 13 04 for removal of paints and varnishes; 10 13 04 disposal of lime and hydrated lime products.
DISPOSAL
Do not enter product in its original concentration into drains or open waters. Do not store at public waste disposal sites. In case of conduction into adapted biological purification plants no disturbances need be expected. The preparation has been estimated by conventional method (Calculated-procedure of EG directive 1999/45/EG) and is classified as non-hazardous for the environment.
Dispose according to local regulations. Empty cans should be disposed of according to local regulations; plastic buckets are 100% PBS, NO. 5, approved for food storage; 100% recyclable if cleaned thoroughly prior to recycling.
ADDITIONAL INFORMATION
This Technical Sheet lists data collected on the basis of technique and experience. Given the multiplicity of use of the product they cannot be binding and the user can not refrain from using common sense and experience for the individual case. This information shall not constitute any legal obligation and no obligation from the seller or point of purchase, or any agreements inferred by employees who sale this product. Insurance or guarantees issued by our employees or employees should always be confirmed separately in writing. User prior to purchase must verify any information about product adaptability and use of the product. Check the exact consumption of product for the surface where product may be applied to determine amount of products needed. The user must verify the color matching before starting work.